Professional tattoo equipment should do more than look impressive on a workstation. It should respond predictably, support the artist’s technique and make demanding sessions easier to manage. That is the thinking behind Vlad Blad tattoo machines and power supplies: equipment developed around the real mechanical and electrical demands of professional tattooing.
BVShop now introduces two distinctive Vlad Blad products for artists who want greater control over how their equipment performs: the Vlad Blad Avenger 3 Pro Wireless Tattoo Machine and the Vlad Blad PowerBox 5 Pro Tattoo Power Supply. One is an exceptionally adaptable wireless machine built to move between techniques. The other is a compact, high-output power supply designed to give compatible wired rotary and coil machines stable, dependable energy.
These are not two components of one required setup. The Avenger 3 Pro is a self-powered wireless machine, while the PowerBox 5 Pro belongs in a wired workstation. Together, however, they show the same design philosophy: give professional artists useful control, remove avoidable interruptions and ensure that the equipment keeps pace with the work.
Why Tattoo Equipment Performance Matters in Professional Work
A tattoo artist makes countless small adjustments throughout a session. Needle grouping, hand speed, machine response, stroke, the characteristics of the working area and the chosen technique all influence how the tool should behave. Equipment that feels appropriate for a fine line may not provide the same response needed for saturated colour packing or strong blackwork. Likewise, a power supply that looks sufficient on paper can become the limiting factor when a wired machine demands high current in rapid peaks.
This is why experienced artists rarely judge a machine by a single specification. Power matters, but so do balance, response under load, adjustability, compatibility and the time required to change a setup. A professional tool earns its place when its features translate into practical advantages at the workstation.
Vlad Blad approaches these challenges from two directions. The Avenger 3 Pro concentrates multiple stroke behaviours and intelligent motor control in one wireless body. The PowerBox 5 Pro focuses on stable electrical delivery for wired machines, including demanding coil setups. Neither product replaces technique or professional judgement. Instead, each gives the artist a more capable foundation on which to apply them.
Vlad Blad: Equipment Shaped by Tattooing and Engineering
Vlad Blad Irons grew from founder Vladislav Barikhin’s long-standing interest in mechanics, electronics and tattooing. The brand traces its production history to 2007, following years of practical experience with both rotary and coil machines. That background is visible in the way Vlad Blad products are positioned: not as generic studio accessories, but as deliberately engineered tools built around machine behaviour, hit, resistance and working rhythm.
The brand is particularly recognised for bringing traditional machine-building knowledge into modern formats. Mechanical systems such as adjustable stroke and magnetic assistance are combined with electronic motor management, replaceable batteries and compact power architecture. For artists, the appeal lies in this meeting point between a tactile, responsive machine feel and the convenience expected from contemporary professional equipment.
At BVShop, the current Vlad Blad selection is focused and easy to understand. The Avenger 3 Pro is for artists looking for one highly adaptable wireless machine. The PowerBox 5 Pro is for professionals who want to get consistent performance from wired rotary or coil machines. Each solves a different workstation problem.
Vlad Blad Avenger 3 Pro Wireless Tattoo Machine
What Is the Avenger 3 Pro?
The Vlad Blad Avenger 3 Pro is a professional wireless hybrid tattoo machine designed to cover a broad range of techniques without requiring the artist to change machines between every stage of a project. Its defining feature is the MultiStroke™ system, which provides six selectable stroke lengths: 3.2, 3.5, 3.8, 4.2, 4.7 and 5.5 mm.
This is more than a wide numerical range. Shorter and medium stroke positions can support controlled shading, softer transitions and versatile everyday work, while longer positions provide the more assertive response often chosen for confident lining and dense packing. The artist can adjust the machine to the task rather than forcing one fixed stroke to perform every role.
The mechanism is adjusted on the machine without full disassembly or a screwdriver. For professionals who move from outlining to shading or colour within the same session, that flexibility can simplify planning and reduce the number of machines required at the workstation.
Who Is It For?
The Avenger 3 Pro is particularly relevant to experienced tattoo artists who use several techniques, work across different styles or want to reduce their dependence on multiple fixed-stroke machines. It can also suit ambitious artists building a premium setup and looking for a machine with enough adjustment range to grow alongside their technique.
Its strongest 5.5 mm setting is intended for a skilled, deliberate hand. A broad adjustment range offers freedom, but it also makes correct technique, machine familiarity and responsible setting selection essential. Artists who prefer a very light pen-shaped tool or who use only one specialised technique may decide that a simpler fixed-stroke machine better matches their personal workflow. The Avenger 3 Pro is most compelling when its adaptability will genuinely be used.
What Can It Be Used For?
With six stroke positions and a controlled frequency range, the Avenger 3 Pro can be configured for a wide selection of professional tattoo work, including:
- fine to bold linework, depending on the chosen stroke, grouping and technique;
- soft shading, grey wash and smooth tonal transitions;
- whip shading and more expressive textural work;
- colour packing and solid black application;
- small detailed pieces as well as larger, multi-stage projects;
- workflows that would otherwise require several machines with different stroke lengths.
The machine is compatible with standard tattoo cartridges and can also be configured for conventional needles with an appropriate grip and setup. Compatibility does not mean that every cartridge behaves identically: membrane resistance, needle grouping and manufacturer design still affect the feel of the machine. Professional testing and careful adjustment remain part of the process.
Why the MultiStroke System Changes the Workflow
Many adjustable machines offer a relatively narrow working range. The Avenger 3 Pro extends from 3.2 to 5.5 mm, creating meaningful separation between its softer and more forceful positions. This allows an artist to change not only the length of the needle movement, but the character of the setup.
For a project that combines several techniques, the practical benefit is continuity. The artist can keep the same familiar body and balance while adapting the stroke for a different task. There is less need to move between several motors, grips and battery interfaces. That can make a compact workstation feel more organised, particularly for guest spots, conventions or artists who travel regularly.
MultiStroke should always be locked precisely into a marked position and fully tightened before operation. The official manufacturer instructions warn against operating the machine with the adjustment screw loose or positioned between marks. This is a professional mechanism, and its convenience depends on correct handling.
M3Pro Brushless Motor and Intelligent Response
At the centre of the Avenger 3 Pro is the 12.6 W M3Pro brushless motor. Hall-effect sensors monitor rotor speed, allowing the electronics to regulate the machine across a wide operating range. Vlad Blad combines this motor with several systems designed to shape its response.
- DirectPower™ supports consistent motor output across the speed range.
- StableHit™ responds to changes in needle pressure and cartridge resistance to help maintain a steady operating feel.
- Antigravity uses magnetic assistance to counter cartridge membrane resistance.
- SkinResponse™ influences needle contact behaviour to support efficient, controlled pigment placement.
- Start-Stop can stop the motor after the machine remains stationary and restart it when the machine is lifted, depending on the selected setting.
For the artist, these systems are intended to reduce the amount of performance lost when load conditions change. They do not automate tattooing and they cannot compensate for unsuitable technique. Their value is in giving the artist a more stable and responsive tool while the hand remains in control.
Wireless Power That Fits a Long Session
The Avenger 3 Pro uses a replaceable Li-ion 18500 battery, with Panasonic NCR18500A recommended by the manufacturer. Runtime is stated at up to approximately seven hours under average settings, although actual working time depends on operating frequency, stroke choice, cartridge resistance, battery condition and working habits.
Fast charging is another practical advantage: the manufacturer states that 15 minutes of charging can provide about 1.5 hours of operation. The battery can be charged inside the machine through USB-C or in a suitable external charger. Because the battery is replaceable, artists can prepare a spare and exchange it instead of placing the entire machine out of use during a long day.
The official manual specifies an unprotected 18500 battery and stresses correct polarity. Artists should follow the supplied manual rather than treating replaceable battery compatibility as permission to use any cell that physically fits.
Ergonomics and Construction
The aerospace-grade aluminium body weighs approximately 134 g without the battery and 167 g with it. The Avenger format is different from a conventional straight pen, so balance and grip preference are personal considerations. Its design distributes the motor, mechanism and battery across a compact body intended to remain controlled during long sessions.
For artists accustomed to very slim pens, the first impression may feel unfamiliar. For those who value a substantial, responsive tool with hybrid machine character, the shape and weight distribution may be part of the attraction. As with any premium tattoo machine, hands-on comfort should be considered alongside the specifications.
Avenger 3 Pro Specifications
| Specification | Vlad Blad Avenger 3 Pro |
|---|---|
| Machine type | Wireless hybrid tattoo machine |
| Stroke positions | 3.2 / 3.5 / 3.8 / 4.2 / 4.7 / 5.5 mm |
| Motor | M3Pro brushless motor, 12.6 W |
| Battery | Replaceable Li-ion 18500; Panasonic NCR18500A recommended |
| Stated runtime | Up to approximately 7 hours, depending on use |
| Charging | USB-C in-machine charging or compatible external charger |
| Weight | Approximately 134 g without battery / 167 g with battery |
| Body material | Aerospace-grade aluminium |
| Compatibility | Standard tattoo cartridges; conventional needles with suitable setup |
Professional Positioning
The Avenger 3 Pro should be viewed as a premium all-rounder for artists who want meaningful mechanical adjustment in a wireless format. Its value is not simply that it has six stroke numbers. It is the ability to move between distinctly different machine behaviours while keeping one familiar platform in the hand. For multi-style artists, travelling professionals and studios seeking a highly adaptable flagship machine, it offers a compelling alternative to maintaining several separate wireless devices.
Vlad Blad PowerBox 5 Pro Tattoo Power Supply
What Is the PowerBox 5 Pro?
The Vlad Blad PowerBox 5 Pro is a compact digital tattoo power supply designed for professional wired rotary and coil machines. Its role is simple but fundamental: provide stable voltage and sufficient current when a machine’s load changes rapidly.
A tattoo machine does not draw power as one perfectly even stream. Its demand changes repeatedly as the mechanism accelerates, encounters resistance and completes each cycle. A power supply can display a modest average current while still needing to meet much higher momentary peaks. If it cannot respond to those peaks, a capable machine may feel weaker or less consistent than it should.
The PowerBox 5 Pro is engineered around this reality. It provides a 1.5–19 V output range, up to 8 A peak current and 5 A continuous current. That capacity is especially relevant to powerful coil machines, but it also supports stable operation from wired rotary equipment.
Who Is It For?
The PowerBox 5 Pro is for tattoo artists who prefer a wired workstation, continue to rely on coil machines or want one serious power source for several compatible machines. It is also a strong option for studios that need a compact supply with physical controls, clear voltage feedback and repeatable presets.
It is not designed to power the wireless Avenger 3 Pro, which uses its own battery system. Instead, it complements a broader professional equipment collection by supporting RCA or clip-cord-based setups, depending on the connected machine and cable configuration.
What Can It Be Used For?
- supplying stable power to professional coil tattoo machines;
- running compatible wired rotary tattoo machines;
- saving frequently used voltage levels for different machines or workflow stages;
- helping demanding machines start reliably at lower voltage;
- building a compact permanent workstation or portable convention setup;
- working with or without a footswitch, according to the chosen operating mode.
Why Peak Current Matters
Voltage is the specification artists notice first, but available current determines whether the power supply can maintain that voltage when the connected machine demands more energy. This is particularly important with coil machines, where rapid armature movement can create strong short-duration loads.
The PowerBox 5 Pro is rated for 8 A peak and 5 A continuous current. In practical terms, that gives the unit headroom to support demanding equipment without the power supply becoming the obvious bottleneck. It does not make every machine run identically, and it cannot correct mechanical tuning problems, overheating coils, damaged cables or worn components. What it can do is provide a stable electrical foundation so that a correctly maintained machine can perform as intended.
Launch Control for Low-Voltage Starts
Some machines or cartridges require extra energy at startup, even when the artist wants to work at a lower running voltage. A common workaround is to raise the voltage to start the machine and then lower it again. Vlad Blad’s Launch Control system handles this initial demand automatically at low voltage and then returns to normal power delivery.
This can be useful with high-resistance cartridge membranes and hard-starting rotary or coil setups. Launch Control is intended to improve startup consistency, not to encourage an artist to operate a machine outside its manufacturer’s recommended range. The correct working voltage still depends on the connected machine, its tuning and the artist’s technique.
Four Memory Presets and Tactile Control
The PowerBox 5 Pro stores four voltage presets. An artist can use these for different machines, common working ranges or stages such as lining, shading and packing. Instead of repeatedly returning to a remembered number, the required preset can be recalled and then refined in 0.1 V steps.
Physical buttons provide tactile feedback, and a longer press adjusts the voltage more quickly. The large numerical display is designed for easy reading at the workstation. The unit can be operated without a footswitch or in trigger mode, while footswitch use remains available for artists who prefer a traditional setup.
Compact Construction for a Clean Workstation
Measuring approximately 35 × 53 × 53 mm, the PowerBox 5 Pro takes up little workstation space. Its one-piece aluminium housing is easy to cover with a standard barrier bag, while a strong magnetic base secures it to suitable metal surfaces. A rubber base supports stability on non-magnetic worktops.
The compact size is useful in busy studios, mobile setups and convention booths where every centimetre matters. The supplied universal power adapter also supports travel between regions, though artists should always confirm local plug and electrical requirements before use.
According to Vlad Blad, every PowerBox 5 Pro undergoes a 24-hour stress test involving 4,320 high-load cycles. That does not remove the need for correct care, intact cables and appropriate barrier protection, but it reflects the professional duty cycle for which the unit is positioned.
PowerBox 5 Pro Specifications
| Specification | Vlad Blad PowerBox 5 Pro |
|---|---|
| Equipment type | Digital tattoo power supply |
| Output voltage | 1.5–19 V |
| Current capacity | 8 A peak / 5 A continuous |
| Voltage adjustment | 0.1 V steps |
| Memory | 4 voltage presets |
| Machine compatibility | Compatible wired rotary and coil tattoo machines |
| Operating options | Footswitch-free operation and trigger mode; footswitch compatible |
| Dimensions | Approximately 35 × 53 × 53 mm |
| Workstation support | Magnetic attachment and rubber anti-slip base |
| Housing | One-piece aluminium body |
Professional Positioning
The PowerBox 5 Pro is best positioned as a compact, high-capacity power foundation for artists who want their wired machines to respond consistently. It is particularly attractive to coil-machine users, but its stable output, presets and low-voltage startup support also make it relevant to wired rotary setups. Rather than adding unnecessary screens or menus, it concentrates on the functions professionals use repeatedly: reliable delivery, fast recall and straightforward control.
Avenger 3 Pro vs PowerBox 5 Pro: Two Different Roles
The two products should not be compared as substitutes. One is a complete wireless tattoo machine; the other powers separate wired machines. The useful question is which type of workflow you want to strengthen.
| Professional Need | Avenger 3 Pro | PowerBox 5 Pro |
|---|---|---|
| Primary role | Complete wireless tattoo machine | Power source for compatible wired tattoo machines |
| Best suited to | Artists wanting one adaptable machine for multiple techniques | Artists using wired rotary or coil machines |
| Main form of control | Six stroke positions plus electronic motor response | Stable voltage, current headroom and four presets |
| Mobility | Wireless, battery-powered workflow | Compact but requires mains power and machine cable |
| Key advantage | Changes machine behaviour without swapping devices | Helps compatible wired machines receive consistent power under load |
| Does it require the other product? | No | No |
How to Choose the Right Vlad Blad Equipment
Choose the Avenger 3 Pro if versatility is your priority
The Avenger 3 Pro makes the strongest case when one session regularly includes several kinds of work. If you want to move from softer shading to stronger linework or packing while retaining the same machine platform, six stroke settings provide real creative and practical range. It is also the natural choice for artists who want to remove cables and a separate power unit from their primary setup.
Choose the PowerBox 5 Pro if your wired machines deserve a stronger foundation
If you already own trusted coil or wired rotary machines, the PowerBox 5 Pro can improve the electrical side of the workstation without asking you to replace those tools. Its current capacity, stable output and Launch Control are especially relevant when a machine has significant startup or peak-load demands.
Choose according to your actual working habits
A premium specification is valuable only when it answers a real need. Consider how many techniques you perform in a typical week, whether you prefer wireless freedom or a fixed station, how much weight feels comfortable in your hand and which machines you already own. An artist with a carefully tuned collection of coils may gain more from the PowerBox 5 Pro. A travelling multi-style artist may find the Avenger 3 Pro transforms the entire setup.
What These Tools Can Add to a Professional Studio
High-quality equipment is not a shortcut to high-quality tattooing. Training, hygiene, design judgement, hand control and experience remain fundamental. The role of professional hardware is to make the technical side of the process more predictable so the artist can concentrate on the work.
The Avenger 3 Pro can reduce machine changes, cable management and duplicated equipment. The PowerBox 5 Pro can organise several common voltage choices and provide the current reserve demanded by powerful wired machines. In different ways, both products aim to remove friction from the session.
There is also a business consideration. Reliable, adaptable equipment can help a studio prepare for a wider range of projects without cluttering each station with unnecessary devices. For travelling artists, compactness reduces what must be packed. For established studios, repeatable controls make it easier to return to familiar setups while still allowing refinement for each client and project.
Professional Use, Hygiene and Equipment Care
Both products are intended for professional tattoo environments and should be handled according to the supplied manufacturer instructions. Protect equipment from cross-contamination with suitable barriers, change barriers between clients and clean non-disposable surfaces only with methods compatible with the equipment materials.
The Avenger 3 Pro must not be placed in an autoclave or dry-heat steriliser. The official manual specifies alcohol-based products for cleaning relevant external components and warns that water-based disinfectant solutions may cause corrosion. The artist should also check battery polarity, keep contacts clean and never operate the MultiStroke mechanism between marked positions.
The PowerBox 5 Pro should be covered appropriately while remaining visible and controllable. Inspect machine cables, power leads and footswitch connections regularly. Stable performance from the power unit cannot compensate for a damaged cable, an incorrectly tuned machine or overheated components.
Always follow the current manual supplied with the exact product. Do not copy another artist’s operating values without assessing the machine, needle grouping, cartridge resistance, technique and working area. Responsible professional use means understanding both the equipment’s capabilities and its limits.
Frequently Asked Questions About Vlad Blad Tattoo Machines and Power Supplies
1. Is the Vlad Blad Avenger 3 Pro a rotary or coil tattoo machine?
The Avenger 3 Pro is a motor-driven hybrid tattoo machine. It uses a brushless M3Pro motor while incorporating mechanical systems intended to create a responsive, powerful machine character. It is not a traditional electromagnetic coil machine.
2. Does the Avenger 3 Pro need the PowerBox 5 Pro?
No. The Avenger 3 Pro is wireless and runs from its own replaceable battery. The PowerBox 5 Pro is designed for separate wired rotary and coil tattoo machines. BVShop offers them as two different professional equipment solutions, not as a mandatory pair.
3. How many stroke lengths does the Avenger 3 Pro have?
It provides six marked stroke positions: 3.2, 3.5, 3.8, 4.2, 4.7 and 5.5 mm. This range allows the machine’s behaviour to be adapted for different techniques. The adjustment must always be placed exactly on a marked setting and tightened correctly before the machine is used.
4. Is the Avenger 3 Pro suitable for every tattoo style?
Its adjustment range makes it suitable for many professional techniques, from controlled shading to linework and packing. That does not mean one setup is appropriate for every task. Cartridge choice, frequency, stroke, hand speed and technique must be selected by a trained artist for the specific project.
5. How long does the Avenger 3 Pro battery last?
The manufacturer states up to approximately seven hours under average working conditions. Runtime varies with motor frequency, stroke setting, cartridge resistance, battery age and use. Because the 18500 battery is replaceable, a prepared spare can help maintain workflow during longer days.
6. Can any 18500 battery be used in the Avenger 3 Pro?
No battery should be selected only because its dimensions fit. The manual calls for an unprotected Li-ion 18500 cell and recommends the Panasonic NCR18500A. Correct polarity is essential. Artists should follow the current product manual and use reputable batteries and chargers.
7. Can the PowerBox 5 Pro run both rotary and coil machines?
Yes, it is designed for compatible wired rotary and coil tattoo machines. The appropriate cable, connection and operating range depend on the connected equipment, so always confirm the machine manufacturer’s requirements before use.
8. What is Launch Control on the PowerBox 5 Pro?
Launch Control temporarily supports a machine that needs additional energy to start at a low selected voltage. It is intended to reduce stalling with demanding machines or cartridges and then disengages when that assistance is no longer required.
9. Why does the PowerBox 5 Pro offer four memory presets?
The presets allow artists to store commonly used voltage levels for different machines or workflow stages. They save time when returning to a familiar starting point, while 0.1 V adjustment still allows precise refinement for the current setup.
10. Which Vlad Blad product should a professional artist choose first?
Choose according to the equipment you want to use. If you need a complete, adaptable wireless machine, start with the Avenger 3 Pro. If you already own wired rotary or coil machines and want a compact, stable power source, the PowerBox 5 Pro is the relevant choice. Some professionals may use both in the same studio, but for different machines and workflows.
Final Thoughts: Vlad Blad Equipment for Artists Who Want More Control
The most interesting professional tools are not those with the longest feature lists. They are the ones whose engineering can be felt in everyday work. The Vlad Blad Avenger 3 Pro Wireless Tattoo Machine turns stroke adjustment, motor intelligence and replaceable battery power into a flexible platform for multi-technique artists. The Vlad Blad PowerBox 5 Pro Tattoo Power Supply concentrates stable output, high current capacity and quick control into an exceptionally compact unit for wired workstations.
Both products reward artists who understand their equipment and want to shape its response deliberately. Whether the priority is wireless versatility or stable power for a trusted rotary or coil machine, the Vlad Blad selection at BVShop offers a serious upgrade path for professionals who expect their tools to work as hard as they do.
Discover professional Vlad Blad tattoo machines and power supplies at BVShop, and choose the equipment that fits the way you work.
